Product Image
Item Name
Price
This is the small bolt type which was used for all models from RV1 to VK and some CL models. Other CL and CM models, and any earlier models which...
$44.00 Add:
Re-key your doors and ignition to use the same key. Ignition Barrel is exact replacement for all models from RV1-VG. Door Barrels are exact...
$80.00 Add:
Suits all models from RV1 - VG
$22.00 Add:
For use with Ballast Resistor
$58.00 Add:
For use with Ballast Resistor only. Made in Japan
$39.00 Add:
$46.00 Add:
If your indicator refuses to cancel after turning a corner, chances are one of the tabs has broken off. A common problem which is easily fixed with a...
$25.00 Add:
Indicator Lens as found on the front and rear of various VC-VG models. Clear. Quality Australian-made product.
$40.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models.
$14.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models.
$20.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models. This is the larger, more elaborate type...
$20.00 Add:
Gasket to suit Indicator Lens as found on the front and rear of various VC-VG models.
$5.50 Add:
Indicator Lens as found on the front and rear of various VC-VG models. Orange.
$35.00 Add:
Salvaged condition; all have minor surface rust on stalk but knob is not cracked
$20.00 Add:
A hard-to-find part. If you turn your original steering wheel upside-down you will notice a steel ring encircling the steering shaft spline socket....
$7.00 Add:
Before ordering this product, please note: you may only need the Cancelling Cam, which is much cheaper! If you are having an issue such as the...
$110.00 Add:
Standard bulb as used in all dashboard bayonet applications. Note VF - CM dashboards also include wedge type bulbs
$1.00 Add:
Round Wiring Harness Connector to join Instrument Panel PCB. Has part number 2791083, which suits the following models: VC Sedan & Utility Up to:...
$18.00 Add:
$22.00 Add:
New, wrapped in tissue paper to prevent scratching
$44.00 Add:
$10.50 Add:
Grubby but will clean up ok. Small hole above armrest, hard to see when installed. Backing board ok.
$55.00 Add:
Nice condition. Some minor overspray that can be cleaned off. Backing board is ok as well.
$60.00 Add:
Damage to trailing edge of lower 2 panels. Some overspray that could be cleaned off.
$27.00 Add:
Grubby but will clean up ok. Stainless strip good but carpet faded. Small hole above armrest that will be obscured by armrest when installed. Good...
$65.00 Add:
Perfect condition. Even the backing board is good enough to re-use.
$65.00 Add:
Grubby but could be cleaned up. No nicks or damage to vinyl. Carpet in crap condition, could be dyed or replaced. Stainless trim is good.
$50.00 Add:
Good Condition, minor hole over armrest which will be mainly hidden by the armrest pad. Some overspray which can be cleaned off.
$40.00 Add:
$1.00 Add:
Nobody likes to have their nuts seized. Here is the solution to the bang noise you just heard when you tried to tighten your panel nuts up
$1.75 Add:
To suit RV1 - VG Quality digital print
$19.00 Add:
These are the brackets used to mount the Front Sway Bar to the K-Frame
$25.00 Add:
These are the bushes to suit the aftermarket brackets used to mount an 18mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 20mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 22mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 23mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 23mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 25mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 27mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 30mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
Quality kit with braided sheathing
$110.00 Add:
Quality kit with braided sheathing
$110.00 Add:
Suits all models from AP5 to CM except VF/VG Hardtop. Sold individually.
$19.50 Add:
Suits VF - VG Hardtop
$9.00 Add:
Suits VF - VG Hardtop
$9.00 Add:
An affordable alternative to buying new lower ball joints if the only problem with your existing ones is perishing rubber. Suits all models,...
$7.70 Add:
Reproduced for the first time ever, this lower boot strip for your VC Valiant is copied exactly from the original and is available only from this...
$44.00 Add:
Lower than original profile so you can turn that torsion bar adjustment bolt a few more times! Sold individually. Includes nut.
$25.00 Add:
Full kit that includes inner and outer metal sleeves
$84.00 Add:
Salvaged; straight but pitted and requires rechroming. This one is the side with the mounting hole as per the photo.
$30.00 Add:
Salvaged; straight but pitted and requires rechroming. This one is the side without the mounting hole as per the photo.
$30.00 Add:
To suit both ute and wagon
$36.00 Add:
Top quality Nolathane brand lowering block kit including U-bolts, extended nuts, washers, and extruded (not the cheaper cast type) blocks. Hey, they...
$125.00 Add:
Top quality Nolathane brand lowering block kit including U-bolts, extended nuts, washers, and extruded (not the cheaper cast type) blocks. Hey, they...
$125.00 Add:
Top quality Nolathane brand lowering block kit including U-bolts, extended nuts, washers, and extruded (not the cheaper cast type) blocks. Hey, they...
$125.00 Add:
Top quality Nolathane brand lowering block kit including U-bolts, extended nuts, washers, and extruded (not the cheaper cast type) blocks. Hey, they...
$125.00 Add:
Top quality Nolathane brand lowering block kit including U-bolts, extended nuts, washers, and extruded (not the cheaper cast type) blocks. Hey, they...
$125.00 Add:
To suit AP5 - VC Quality digital print
$14.00 Add:
$55.00 Add:
Clevite brand
$80.00 Add:
Suits all Slant and Hemi engines
$4.50 Add:
These original salvaged conical washers are to suit Slant and V8 engines.
$5.00 Add:
Unavailable as a factory-correct reproduction, these original salvaged washers feature the concave shape. Suitable for both Slant and Hemi
$5.00 Add:
This kit is to suit the rebuild of the AP5 - VC Screw Top Master Cylinder
$64.00 Add:
$185.00 Add:
I bought this with a 1950's car radio and wondered what it was. A completely sealed cylinder with something moving (not rattling, but moving like it...
$16.00 Add:
This will fit all Torqueflite transmissions from VF to CM. It can be used to replace the earlier one pin type, which is no longer available, with...
$55.00 Add:
NOS Wibroc Mirror Head, still in the box as pictured. Stainless is perfect since it still has the protective covering on it. Mirror has no foxing....
$50.00 Add:
Standard bulb as used in all number plate light assemblies
$1.00 Add:
Canister type oil filter to suit RV1/SV1 Slant and AP6/VC V8
$25.00 Add:
Quality Ryco Z9
$12.00 Add:
Suits all models
$16.50 Add:
Salvaged Oil Pump Drive Gear to suit Small Block
$50.00 Add:
Kit to suit the rebuild of Australian Slant 6 Oil Pumps
$280.00 Add:
This door is 100% rust free but has a large dent on the upper inside panel. Aside from this it is straight with original paint and the stainless...
$150.00 Add:
This door is straight and 100% rust free. Crappy matt black spray can paint job is disguising possibly the nicest door you could ever hope to find....
$200.00 Add:
This door is straight but has one rust-through area on the inside and outside of the trailing edge as shown. Aside from this there are no other rust...
$100.00 Add:
$14.00 Add:
High temp plastic construction to suit 1/2" PCV Grommet
$12.00 Add:
To suit various models from AP5
$24.00 Add:
1/2" NPT. Suits V8
$5.00 Add:
3/8" NPT. Suits V8
$5.00 Add:
$110.00... more info
$1,100.00 Add:
$1,100.00 Add:
$1,100.00 Add:
$1,100.00 Add:
$340.00 Add:
$340.00 Add:
$340.00 Add:
$340.00 Add:
$340.00 Add:
To suit all VC models and V8 AP6
$55.00 Add:
Suits TorqueFlite 904
$18.50 Add:
$5.85 Add:
$13.20 Add:
NOS bypass hose to suit 273 with original Mopar sticker. Part number is 2465085. This is stamped on about half of the stickers. Does not come with...
$24.00 Add:
$11.00 Add:
$28.90 Add:
$17.50 Add: