Product Image
Item Name
Price
Suits all models. If your Fuel Gauge is stuck on empty, the problem could be a poor ground through the Ground Strap. This is the stainless steel...
$22.00 Add:
To suit only models with fuel sender pickups that have been enlarged to 3/8"
$25.00 Add:
To suit all models with standard 5/16" sender tube
$37.50 Add:
Suits all models
$9.00 Add:
Correct part for models with J-Bolt. Models which do not use this type of J-bolt may still use this if: the hole in the chassis rail in which the...
$22.00 Add:
$0.50 Add:
Exact reproduction of factory fitted item for AP5 - VK, suitable for all models from RV1 - CM
$28.00 Add:
For use with Ballast Resistor
$58.00 Add:
For use with Ballast Resistor only. Made in Japan
$39.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models.
$14.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models.
$20.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models. This is the larger, more elaborate type...
$20.00 Add:
A hard-to-find part. If you turn your original steering wheel upside-down you will notice a steel ring encircling the steering shaft spline socket....
$7.00 Add:
Standard bulb as used in all dashboard bayonet applications. Note VF - CM dashboards also include wedge type bulbs
$1.00 Add:
$10.50 Add:
$1.00 Add:
Nobody likes to have their nuts seized. Here is the solution to the bang noise you just heard when you tried to tighten your panel nuts up
$1.75 Add:
These are the brackets used to mount the Front Sway Bar to the K-Frame
$25.00 Add:
These are the bushes to suit the aftermarket brackets used to mount an 18mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 20mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 22mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 23mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 23mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 25mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 27mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 30mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
Quality kit with braided sheathing
$110.00 Add:
Quality kit with braided sheathing
$110.00 Add:
Suits all Slant and Hemi engines
$4.50 Add:
These original salvaged conical washers are to suit Slant and V8 engines.
$5.00 Add:
Unavailable as a factory-correct reproduction, these original salvaged washers feature the concave shape. Suitable for both Slant and Hemi
$5.00 Add:
This will fit all Torqueflite transmissions from VF to CM. It can be used to replace the earlier one pin type, which is no longer available, with...
$55.00 Add:
Standard bulb as used in all number plate light assemblies
$1.00 Add:
Suits all models
$16.50 Add:
Suits TorqueFlite 904
$18.50 Add:
$11.00 Add:
$28.90 Add:
Standard Bulb used to light the Radio Dial and several other interior applications
$1.00 Add:
Top quality hose, made in Australia and individually tested to 3000psi. Hoses are made to your order: please e-mail us after placing an order if you...
$55.00 Add:
Suits TorqueFlite 904, Borg Warner 3 Speed Manual, Borg Warner 35 Automatic
$32.00 Add:
Quality SuperPro polyurethane product. 4 bushes are supplied; enough to do 1 car
$45.00 Add:
Set includes enough to do one rear shock; 4x Washers and 2x Nuts
$19.00 Add:
Quality US-made product. Sold as a pair.
$155.00 Add:
Suits all models with 34mm dia front leaf spring bushes. Price is for 4 Bushes, enough for 1 car
$24.00 Add:
Suits all models with 34mm dia front leaf spring bushes. Price is for a pair; enough to do 1 car
$38.00 Add:
Quality product. Sold as a set of 4. RV1 - VH models require 2 sets per car as they are used for upper and lower shackle bushes. VK - CM models only...
$20.00 Add:
Quality product. Sold as a set of 4. RV1 - VH models require 2 sets per car as they are used for upper and lower shackle bushes. VK - CM models only...
$45.00 Add:
To suit Slant 6, Hemi and Small Block engines running camshafts with lift over 0.500". Exceeds E49 and E55 factory specifications. Sold individually...
$15.50 Add:
To suit Slant 6, Hemi and Small Block. Sold individually so 6 cylinder owners can order 12 and V8 owners can order 16
$13.00 Add:
BP5ES
$5.60 Add:
BCP5ES
$5.60 Add:
Quality Australian-made sintered bronze product. Suits all manual transmissions.
$11.00 Add:
Suits manual Steering Box
$35.00 Add:
Suits manual Steering Box
$15.00 Add:
Steering Shaft to Steering Box Coupling Repair Kit. Take the play out of your steering and make your steering more responsive. Fits all models.
$32.00 Add:
Suits all models
$1.50 Add:
Suits all models
$49.00 Add:
To suit all 6 cylinder models
$4.50 Add:
Opening temp = 82 degrees
$13.20 Add:
If your Tie Rod Ends are fine but the boot is perished, here is your affordable answer
$5.85 Add:
Pair of MDI Seals. Suits all models
$26.00 Add:
To suit all models, auto or manual; note that this product is imported from the US so only features one thread, not two. Australian mounts were...
$49.00 Add:
To suit all Valiant models except those with Sure-Grip Limited Slip Diffs
$22.00 Add:
Includes nuts and washers.
$30.00 Add:
Nolathane or Moog brand
$17.00 Add:
Quality Australian-made Mackay Rubber product. 4 required per car
$15.00 Add:
Used to adjust camber and caster. One set is enough to do both sides of 1 Upper Control Arm.
$40.00 Add:
Suits all models. Order 12x for Hemi or Slant, 16x for V8
$3.00 Add:
NOS Bosch RE55 Voltage Regulator. In storage for over 20 years, this Australian-made unit has been waiting long enough to become part of your project!
$45.00 Add:
1-5/8", brass. Suits Slant, Hemi and V8 models
$5.00 Add:
1-5/8", brass. Suits Slant, Hemi and V8 models
$5.00 Add:
Gasket that goes under the Wheel Cylinder. Suits all models
$4.00 Add:
Includes flat washer
$2.50 Add:
$2.00 Add:
$2.00 Add:
To suit all models. Generic, inoffensive-looking assembly; kit includes everything from button to nozzles
$32.00 Add:
$3.00 Add:
$3.00 Add:
Black OEM-style wiring harness tape, as per original
$15.00 Add:
Suits all models, excluding those fitted with solid disc brakes. Wasp brand
$49.00 Add:
Suits all models, excluding those fitted with solid disc brakes
$43.00 Add:
An affordable alternative to buying new lower ball joints if the only problem with your existing ones is perishing rubber. Suits all models,...
$7.70 Add:
$50.00 Add:
Copper-faced gasket, old stock, brand unknown
$11.00 Add:
To suit all 9" drum brakes. Kit includes springs and clips to suit one pair of drum brakes
$36.00 Add:
5-3/4" (146mm) diameter to suit: RV1 SV1 VF VIP VG VIP Chrysler by Chrysler CL CM High Beam Single Filament Single Beam
$22.00 Add:
5-3/4" (146mm) diameter to suit: RV1 SV1 VF VIP VG VIP Chrysler by Chrysler CL CM High/Low Sealed Beam
$22.00 Add:
Lower than original profile so you can turn that torsion bar adjustment bolt a few more times! Sold individually. Includes nut.
$25.00 Add:
Full kit that includes inner and outer metal sleeves
$84.00 Add:
Suits all Valiant models except R Series For L/H outer and R/H inner
$16.50 Add:
Suits all Valiant models except R Series For R/H outer and L/H inner
$16.50 Add:
Suits all models except RV1.
$24.00 Add:
If your Upper Ball Joint is fine but the rubber boot has perished, fit a new rubber boot and save around $20 per side. Suits all models except RV1.
$5.75 Add:
To suit all Late VC - CM
$14.50 Add:
Suits all models from VC to CM
$22.00 Add:
Suitable for the Rear of any 2-door VE - CL model. Not the original type but looks the part and matches the front Armrests
$74.00 Add:
To suit: VF, VG, VH, VK and... VE with 273 from engine number VE6-2288 and up VE with 225 with 2bbl carburettor and engine number prefix of LVE8D VE...
$14.00 Add:
$50.00 Add:
$18.00 Add:
Salvaged but made from much heavier gauge steel than the reproductions. Looks galvanised but is probably plated. Will clean up ok
$20.00 Add: