Product Image
Item Name
Price
Covered in primer overspray that can be cleaned off. Some damage to middle panel. Backing Board needs replacement.
$27.00 Add:
Covered in overspray and pretty rough. Would look better cleaned up and on a new board. Would also look better on fire. Damage to trailing edge of...
$25.00 Add:
To suit RV1/SV1 Quality digital print
$17.00 Add:
This kit is to suit the rebuild of the RV1-SV1 Master Cylinder
$45.00 Add:
$220.00 Add:
The ring and bracket that attaches the Oil Filter Canister to the engine block. This one has been chrome plated in the past but requires stripping...
$35.00 Add:
$20.00 Add:
$21.80 Add:
$22.00 Add:
This is an original piece of glass for a rear door. The same piece of glass was used for both sides; the Armourplate logo is reversed when viewed...
$50.00 Add:
$60.00 Add:
$60.00 Add:
Includes Bearing, Lock Collar and Rear Axle Seal. One set per wheel.
$86.00 Add:
$18.00 Add:
$150.00 Add:
$99.00 Add:
$52.00 Add:
$38.00 Add:
Salvaged Crossmember to suit R and S Series Valiant
$90.00 Add:
To suit RV1/SV1 Quality digital print
$16.50 Add:
This is an original piece of glass for the Driver's Side Rear Door. Technically you could use it for the passenger side rear door too since the glass...
$45.00 Add:
Salvaged Window Regulator to suit RV1/SV1 Driver's Side Front Door. Has been ultrasonically cleaned, regreased and tested. Includes linkage arm and...
$60.00 Add:
Ideal if your window sill has been dented or if the mounting holes have been damaged by the screws being replaced by much larger screws. Note that...
$15.00 Add:
Ideal if your window sill has been dented or if the mounting holes have been damaged by the screws being replaced by much larger screws. Note that...
$15.00 Add:
Ideal if your window sill has been dented or if the mounting holes have been damaged by the screws being replaced by much larger screws. Note that...
$15.00 Add:
Ideal if your window sill has been dented or if the mounting holes have been damaged by the screws being replaced by much larger screws. Note that...
$15.00 Add:
Quality Wiper Spring to suit RV1 - SV1 only
$12.00 Add:
This is to suit the small bolt type which was used for all models from RV1 to VK and some CL models. Other CL and CM models, and any earlier models...
$24.50 Add:
This is to suit the small bolt type which was used for all models from RV1 to VK and some CL models. Other CL and CM models, and any earlier models...
$10.00 Add:
This is the small bolt type which was used for all models from RV1 to VK and some CL models. Other CL and CM models, and any earlier models which...
$44.00 Add:
To suit all TorqueFlite transmissions built prior to 1966
$9.00 Add:
To suit all models up to early VG
$74.00 Add:
To suit RV1 and early SV1; one required per car. Quality Australian-made product. Suits all RV1 and SV1 body numbers up to SV1-2-542 and SV1-4-441
$170.00 Add:
To suit RV1 - early AP5 Manual Gearboxes
$42.00 Add:
To suit RV1 - AP5 Manual Gearboxes
$20.00 Add:
Suits RV1 - Early AP5 Unavailable until recently, this item is a bolt-in replacement for your original
$45.00 Add:
$50.00 Add:
Suits all models, excluding those fitted with solid disc brakes. Wasp brand
$49.00 Add:
Suits all models, excluding those fitted with solid disc brakes
$43.00 Add:
An affordable alternative to buying new lower ball joints if the only problem with your existing ones is perishing rubber. Suits all models,...
$7.70 Add:
2 per car required for RV1-SV1, 3 required for VC-VG Also fits VH - CM
$7.00 Add:
6 per car. Suits all models.
$4.50 Add:
This is the part that fits into the slot in the door to screw the Armrest to. Sold individually.
$6.50 Add:
Suits both 3 and 4 Speed Gearboxes. Made from rubber, not nolathane.
$43.00 Add:
$20.00 Add:
Suits all models. Quality product made by an automotive OEM
$8.00 Add:
Standard single filament bulb as used in many factory or aftermarket boot or underbonnet lamp assemblies
$1.00 Add:
Includes key, barrel, clip, and the lever that fits into the latching mechanism. Different length levers are included to suit all models
$32.00 Add:
Suitable for use on all models without modification except RV1/SV1. RV1/SV1 owners will need to replace the plug-type connector on the harness with a...
$16.50 Add:
Polished by hand in the USA and individually bagged to prevent scratching. Includes nyloc nut
$4.50 Add:
2-1/8", brass. Suits all 6 cylinder models
$5.00 Add:
$9.00 Add:
$22.00 Add:
$22.00 Add:
2 required for joint between Z-Tube and Pedal, 1 required between Z-Tube and Clutch Fork Adjuster
$5.00 Add:
Suits all models
$8.00 Add:
Set of 4 Clutch Pivot Bushes
$12.00 Add:
$13.50 Add:
Restoration-correct part to suit all Manual gearbox models
$17.00 Add:
$17.00 Add:
Set of 2 MDI Clutch Torque Tube Linkage Dust Seals
$10.00 Add:
To suit Tail Light / Brake Light and Park Light / Indicator Applications
$1.00 Add:
Heavier grade than the original. Old stock.
$20.00 Add:
Standard generic model
$15.00 Add:
New but looks old as it has been bouncing around the shed for a while
$3.00 Add:
55.6mm Fits all models
$10.00 Add:
Lower Shock Absorber Bush as fitted to base of front shock absorber. An affordable alternative to replacing one of your front shocks if the only...
$13.80 Add:
Genuine Mackay, Australian made. Includes inner tubes.
$80.00 Add:
$4.00 Add:
Ryco Z14. Suits all models
$6.00 Add:
Suits all models
$2.20 Add:
Suits all models. If you are missing a Ground Strap and enough money to buy a new one, buy this crusty old one instead and clean it up
$2.00 Add:
Suits all models. If your Fuel Gauge is stuck on empty, the problem could be a poor ground through the Ground Strap.
$15.00 Add:
Suits all models. If your Fuel Gauge is stuck on empty, the problem could be a poor ground through the Ground Strap. This is the stainless steel...
$22.00 Add:
To suit only models with fuel sender pickups that have been enlarged to 3/8"
$25.00 Add:
To suit all models with standard 5/16" sender tube
$33.00 Add:
Suits all models
$9.00 Add:
Correct part for models with J-Bolt. Models which do not use this type of J-bolt may still use this if: the hole in the chassis rail in which the...
$22.00 Add:
$0.50 Add:
Exact reproduction of factory fitted item for AP5 - VK, suitable for all models from RV1 - CM
$28.00 Add:
For use with Ballast Resistor
$58.00 Add:
For use with Ballast Resistor only. Made in Japan
$39.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models.
$14.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models.
$20.00 Add:
If your indicators are staying on constantly, here is your solution. Two-pin Flasher Can to suit all models. This is the larger, more elaborate type...
$20.00 Add:
A hard-to-find part. If you turn your original steering wheel upside-down you will notice a steel ring encircling the steering shaft spline socket....
$7.00 Add:
Standard bulb as used in all dashboard bayonet applications. Note VF - CM dashboards also include wedge type bulbs
$1.00 Add:
$10.50 Add:
$1.00 Add:
Nobody likes to have their nuts seized. Here is the solution to the bang noise you just heard when you tried to tighten your panel nuts up
$1.75 Add:
These are the brackets used to mount the Front Sway Bar to the K-Frame
$25.00 Add:
These are the bushes to suit the aftermarket brackets used to mount an 18mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 20mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 22mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 23mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 23mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 25mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 27mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
These are the bushes to suit the aftermarket brackets used to mount a 30mm diameter Front Sway Bar to the K-Frame
$17.00 Add:
Quality kit with braided sheathing
$110.00 Add: